Safelite Autoglass Practice Test

These questions are part of the practice quiz. Start practicing

• Which term defines the force per unit area necessary to rupture a bond?
• Molecules that join side by side as well as end to end are described as
• What term describes the interval from urethane extrusion to final glass placement in the pinch weld?
• Which material is a copolymer of isobutane and isoprene, known as a sealant with low recovery, slow cure, and good elongation?
• The attachment at an interface between a substrate and an adhesive or sealant is called
• Which term describes the rubber material that returns to its original dimensions after deformation?
• What is the term for a family of polymers ranging from rubbery to brittle formed by the reaction of a diisocyanate with a polyol, also described as polyurethane?
• Name two common indications that a windshield should be replaced rather than repaired.
• How should you dispose of or recycle old windshields and waste adhesives?
• Which factor most directly impacts the structural integrity of the bond between windshield and frame?
• What term describes the progressive change in the chemical and physical properties of a sealant or adhesive?
• Which term describes a preformed shape such as strips or grommets used to fill and seal a joint or opening?
• What term means the clinging or sticking together of two surfaces?
• What term indicates the duration available to manipulate urethane before curing begins during assembly?
• Which term describes the timing aspect of curing adhesives at a specified environment?
• The ability of a material to return to its original shape after removal of a load is:
• In the standard windshield replacement process, what action follows removing the old windshield?
• Which term describes electrochemical corrosion caused by dissimilar metals in an electrolyte?
• The term for the material's ability to conduct electricity is
• What term describes a surface prepared by wiping with adhesion promoter so it is ready for adhesive bonding?
• Which term is the overall property of returning to original shape after load?
• What could occur if a scope check is not performed before windshield replacement?
• What is the purpose of a post-install test drive check?
• Which term is the ceramic UV-protective windshield band now typically made from zinc or bismuth-based paint?
• Which term expresses pressure and is abbreviated PSI?
• When analyzing a damaged windshield, what is the difference between repairable damage and replacement requirement?
• Any deviation from Safelite's installation practices is a
• The building blocks of polymers are called what?
• Which standard refers to safety standards for windshield adhesive bond-line retention during a crash?
• Why is communication with the customer important during the replacement process?
• Which term describes the total opposition to current flow in an alternating-current circuit?
• Which of the following describes calibration drift?
• Which term is the measure of the total opposition to current flow in an alternating-current circuit?
• The maximum elongation a material can undergo before breaking.
• A windshield dam tape system that holds urethane in place. It maintains the windshield the proper distance from the pinchweld and promotes adhesive cure.
• How should air conditioning or heating vents be used during replacement to prevent condensation or fogging?
• What is the primary purpose of defogging before repair steps?
• What is the ratio of stress to strain called?
• What is the plastic part through which the bead of adhesive is extruded?
• What is a key benefit of performing windshield replacement in a space with adequate lighting?
• Elongation at failure.
• What is the proper approach to disposing of waste during and after installation?
• How should you document the installation for quality assurance and warranty?
• What term describes a set of laboratory conditions designed to produce the results of normal aging in a shorter time?
• Which term refers to the factors that influence the curing of adhesives?
• Resistance of a material to a tensile force (a stretch). The cohesive strength of a material expressed in PSI.
• Which safety standard is commonly referenced for vehicle repair work?
• Which term refers to the surface of an adhesive or sealant to which bonding occurs?
• Which unit is used to quantify viscosity in the material?
• The time between applying the adhesive and the formation of a skin on its surface, after which bonding can no longer take place.
• What is the purpose of primer in some adhesive systems?
• What is the impact of incorrect pinchweld preparation on windshield performance?
• Which term refers to a cured polyurethane bead that has been freshly cut?
• What term describes the amount of adhesive overlap between pinchweld and windshield?
• Which process is moisture-activated and progresses from the exterior toward the interior of the adhesive?
• What key information should be collected before starting a windshield replacement?
• How should you respond to a customer with a pre-existing insurance claim for windshield damage?
• How should you label and track replacement parts to ensure traceability?
• When performing post-installation checks, which key alignment areas should be verified?
• Which type of failure is characterized by pulling the adhesive or sealant loose from the substrate?
• Which statement best describes the purpose of a defogging step before bonding?
• What term describes material that removes contaminants and prepares glass for bonding?
• What term refers to the side window on a passenger car?
• What is a common sign that an ADAS calibration is required after windshield replacement?
• What is the typical consequence of using the wrong type of adhesive during installation?
• The period during which urethane remains workable after extrusion is called
• What is the importance of surface moisture in the bonding area before curing?
• In ADAS recalibration, mounting brackets or reflectors are considered because they influence alignment. Which statement best explains their role?
• How should you handle a customer complaint about a wind noise after replacement?
• The attachment between a substrate and adhesive or sealant is known as the
• What term describes the time required to achieve a complete cure at a given temperature and relative humidity?
• Which term is another name for a pane of glass or windshield?
• If ADAS recalibration is not performed after windshield replacement, what is a likely issue?
• What conditions are ideal for windshield replacement?
• What is the typical warranty period for Safelite windshield replacements, and what factors influence it?
• Part of the light spectrum UV Rays can cause chemical changes in rubber materials.
• Open Time #2 is the maximum period of time that may elapse between application of the adhesive and assembly of the joint.
• Which term describes a class of polymers formed from diisocyanates and polyols?
• If you notice a water leak after windshield replacement, what steps should you take?
• What is the correct procedure for cleaning up during and after installation to maintain shop safety?
• What action should be taken if a wind noise persists after resealing?
• What is the term for the property that describes a liquid's resistance to flow?
• Which term describes a cured polyurethane bead that has been freshly cut?
• What is calibration drift in ADAS, and how is it detected?
• Which factor is directly affected by premature exposure of the adhesive during curing?
• What determines whether a chip repair can be performed during a windshield repair operation?
• Which term refers to the passenger car rear window?
• Which term describes a material that removes contaminants and prepares surfaces for bonding?
• A compound consisting of long chainlike molecules, where the building units in the chain are monomers, is known as what?
• Why is environmental cure time important in adhesive installation?
• In estimating repair feasibility, what is not a determining factor?
• When addressing a water leak after windshield replacement, what action should you take after resealing?
• What role does surface preparation play before applying adhesive?
• What does PPE stand for in safety contexts?
• In materials engineering, what term describes a class of polymers formed from diisocyanates and polyols?
• What name is given to polymers formed by reaction of diisocyanates with hydroxyl groups?
• Which term refers to a preformed shape used to seal a joint or opening, typically made of rubber-like material?
• Difference between 'safety glass' and 'glass standard' used in cars, and which parts have safety glass?
• Which term is abbreviated as PAS or PAAS?
• Which curing mechanism involves moisture from the air diffusing into the adhesive, causing it to cure from the outside toward the center?
• Which term is used for the coating process applied to metal parts by electrically charged paint particles?
• How should weather conditions influence the timing of windshield replacement?
• What is the primary purpose of using a urethane adhesive during windshield replacement?
• Which term refers to the window type bonded directly to the vehicle body without an adjacent frame on the opening?
• Which statement about automotive safety glass is correct?
• What is the correct order of basic steps in a windshield replacement?
• A surface coating generally applied to fill cracks pores or voids in a surface
• The painting method that deposits paint using electrical current is:
• What term refers to a polyurethane adhesive applied by the glass manufacturer to the end of the glass for molding and decorative trim on flush-mounted autoglass?
• Which term describes the initial strength of a material when first applied and not yet cured?
• In adhesive processes, what term refers to the usable period before hardening starts?
• How should you handle a chipped windshield near the edge?
• What is the recommended approach if a survey sticker is damaged during removal?
• Which term denotes the sealant or compound after application in a joint?
• Windshields which contain a polyurethane profile molding around the edges:
• Which statement best describes safe handling and PPE usage when replacing windshields?
• Which polymer family ranges from rubbery to brittle and is formed by the reaction of diisocyanate with a hydroxylic compound?
• What term is used for the sealant or compound after application in a joint, such as urethane bead applied to a pinchweld?
• Which term is a preparatory material that improves adhesion and may inhibit corrosion?
• Which term identifies the ceramic band around the windshield used for UV protection, now typically made from zinc or bismuth-based paint?
• A black ceramic composite applied to the windshield perimeter to protect the urethane adhesive from UV rays is called
• Poisonous or dangerous to humans by swallowing inhalation or contact to eyes and skin.
• Open Time #1 describes the time interval between applying adhesive and when it is no longer workable.
• What term refers to the polymer class produced by the reaction of a diisocyanate with hydroxyl groups?
• What is a safe practice when handling glass to prevent microcracking or breakage?
• Which term describes the ceramic coating applied around the windshield perimeter to protect the urethane adhesive from UV exposure?
• Polysulfide Rubber is a synthetic polymer usually obtained from which compound?
• Which term refers to a coating used to fill pores or voids in a surface?
• In windshield installation, the pinchweld refers to which area?
• What is the risk of improper moisture management during adhesive curing?
• During replacement parts management, which practice supports traceability?
• When evaluating a vehicle for ADAS recalibration after windshield change, which components are typically checked?
• In the example given, water has a viscosity of 1/100 of a poise. This property is called
• Which term describes a surface prepared with adhesion promoter that remains active for bonding for up to eight hours?
• What is the main purpose of allowing a cure time after applying adhesive during windshield replacement?
• Which term describes a rubber material commonly used as the framing rubber for side windows?
• Which term describes something poisonous or dangerous to humans by swallowing or inhalation?
• What is the opening between component parts called?
• Which statement best describes surface cleaning and priming before adhesive application?
• Which combination of information should be collected prior to starting a windshield replacement?
• The stickiness of the surface of a sealant or adhesive.
• How should windshields be stored prior to installation?
• Pressure exerted on a sealant or adhesive in a joint is called
• What property measures a material's resistance to pulling apart?
• What is the term for the time required for primer or activator to dry sufficiently before adhesive can be applied?
• Which term is used to describe the overall duration from extrusion to final placement in bonding processes?
• Which term is a preparatory material designed to improve adhesion between adhesive and certain substrates, and may inhibit corrosion depending on composition and paint thickness?
• A rubber material that returns to approximately its original dimensions in a short time after a lot of deformation:
• What is the primary reason to perform a scope check before beginning work?
• The amount of adhesive overlap between pinchweld and windshield is called what?
• Which method is commonly used to align a new windshield during installation?
• Which regulation specifies that when a vehicle traveling at 30 mph crashes, more than 75% of the adhesive bond-line is retained, with no more than 50% lost on one side?
• During a replacement, how should you test the wind noise after installation?
• Rubber material which is commonly used in the framing plastic of side windows.
• Which term describes an antenna-suitable adhesive that will not interfere with radio reception for windshields with integrated antennas?
• Which term describes the solvent used in a sealant system?
• A safe practice when handling a damaged windshield that could affect airbag deployment?
• What is a 'pocket' in windshield installation terms?
• The measure of the ability of a material to conduct electricity is called
• What should you test during wind noise testing after installation?
• What is the importance of documenting a calibration check outcome after ADAS recalibration?
• Why are torque specs on mounting hardware for trim and molding important?
• What is the purpose of 'bond line' in windshield installation?
• Which type of glass is typically used for a vehicle windshield, and why?
• Which polymer family is formed by diisocyanate and a hydroxylic compound?
• Any material used to seal joints or openings against intrusion of water gasses air or dirt
• What is the British unit of pressure for pound per square inch?
• Which term describes the active period before the material hardens during glazing?
• What is the purpose of windshield sealant and weatherstripping?
• Which component improves adhesion of the adhesive to the vehicle substrate?
• Why is edge damage often not repairable and may require replacement?
• The metal surface in an automobile opening is called which term?
• Polysulfide Rubber is valued as a sealant because it is what?
• A liquid in which another substance can be dissolved.
• Which term describes a fast-setting adhesive with enhanced chemical to speed up bonding?
• Which term refers to a one component urethane adhesive that contains enhanced chemical to speed up bonding?
• Polysulfide Rubber is typically obtained from which compound?
• Which tool is commonly used to remove an old windshield without damaging the pinchweld or surrounding trim?
• Method of deforming a sealed or bonded joint by forcing the substrate to slide over each other
• An adhesive designed to reduce electrical current flow using a carbon black additive is best described as which type of adhesive?
• An adherend. The surface of a sealant or adhesive.
• What should be considered if weather slows cure time and accelerated cure times are available?
• The opposition that a device or material offers to the flow of a direct current
• What does Backlite refer to in automotive terms?
• Which term is used to describe the flow resistance of a liquid?
• Which surfaces should be cleaned before applying urethane to ensure proper adhesion?
• To fill the joints with a sealant is to
• The length of time a sealant or adhesive can be stored and still retain its properties
• Which term describes a sealant with low recovery and slow cure, typically used in glazing applications?
• The ability of a urethane adhesive to support the windshield in the pinchweld opening is called:
• What should be included in the warranty documentation for windshield replacements?
• Which term describes the time period referred to as 'Working Time'?
• The round shaped component on the end of the application gun that dispenses the material is called what?